RT Off-Road's Halogen Light Conversion Kits are an upgrade for the conventional factory sealed beam headlamps. Included in the Headlight Conversion Kit are two halogen bulbs and two cast housings with clear glass lenses. Our kit is DOT and SAE compliant. Includes a pair of 7″ round assemblies and H4 55/60W bulbs.

Référence : 51-JS-6879

Heavy Duty Dual Diaphragm Brake Booster and 1-1/8″ Bore Master Cylinder.Replace rusty, leaky and faulty Brake Booster & Master Cylinders with a HD kit from RT Off-Road. Two performance level kits were designed to specifically cater to the vehicles requirements. The larger bore Master Cylinders are designed for upgrades done to axles with larger brake calipers. The more moderate bore is designed for vehicles with factory brakes, disc brake upgrades and vehicles that require more braking power.Each kit consists of a zinc-coated Brake Booster, Master Cylinder, bench bleeding kit and installation instructions. Installation involves replacing the factory brake booster and master cylinder.

Référence : 51-JS-6943

Eliminate drive line vibrations and increase strength of your NP231 with RT Off-Road's Slip Yoke Eliminator Kit. Each kit includes a replacement output housing, heavy duty main shaft, rear output yoke designed for a double-cardan drive shaft and all necessary hardware. The installation can be performed with the transfer case in or out of the vehicle with basic hand tools. Engineered to function with the factory speedometer sensor/cable and vacuum shift sensor.Fits all Jeep NP231 transfer cases; 1-3/8″ 32-spline main shaft and yoke; converts factory rear slip yoke to a CV style output; Includes installation instructions.Speedometer Drive Gear (4338996) Is Included; For Replacement Seal Use RT24003; For Replacement Bearing Use J8136622 (and remove snap ring); For Replacement Yoke Use 4856142 (1310 CV; 32 Splines); For Replacement Rear Yoke Washer Seal Use 4210973; For Replacement Yoke Nut Use J3182601.

Référence : 51-JS-5842

Black Anodized Throttle Body Spacer Kit; 1″ Thick to Provide a Smoother, Faster and More Dense Air Charge Resulting in HP, TQ and MPG Increases. Kit Includes: Aluminum Spacer, Gasket, Bolts and Washers.

Référence : 51-JS-6911

Front Left Park & Turn Signal Lamp; Clear.

Référence : 51-JS-6884

Heavy Duty Dual Diaphragm Brake Booster and 1″ Bore Master Cylinder.Replace rusty, leaky and faulty Brake Booster & Master Cylinders with a HD kit from RT Off-Road. Two performance level kits were designed to specifically cater to the vehicles requirements. The larger bore Master Cylinders are designed for upgrades done to axles with larger brake calipers. The more moderate bore is designed for vehicles with factory brakes, disc brake upgrades and vehicles that require more braking power.Each kit consists of a zinc-coated Brake Booster, Master Cylinder, bench bleeding kit and installation instructions. Installation involves replacing the factory brake booster and master cylinder.

Référence : 51-JS-6948

Référence : 51-JS-5965

Rear Big Brake Kit; Only Works with 17″ Wheels or Larger; 13.5″ Diameter Rotors; Rotors feature a 5 on 5″ and 5 on 5.5″ Bolt Pattern.Includes Pads, Rotors, Caliper Brackets, Caliper Pin Kit and Red Threadlocker; Utilizes the Factory Brake Caliper.

Référence : 51-JS-6916

RT Off-Road's Clear Light Kits are a DOT-legal way to give the vehicle an all new look. These crystal clear lenses come complete with amber bulbs. The bulbs and lenses included in our kit will install directly into the factory wiring harnesse and body. Installation requires no modifications to the body and can be completed with basic hand tools. Includes 2 clear parking lamps, 2 clear side marker lamps and four (4) amber bulbs.

Référence : 51-JS-6889

Année(s) : 96-06

Improve steering performance with RT Off-Road's Drop Pitman Arm. Lifting your Jeep without addressing the steering angles oftentimes results in bump steer and decreased turning radius. Installation of this drop pitman arm will reduce the operating angle of the drag link, resulting in improved steering feel and less wear on steering parts. Each arm is designed to bolt in place of the factory piece with no interference issues.

Référence : 51-JS-6967

Front Left or Right Stabilizer Bar Link w/ Polyurethane; Not Designed For Lifted Vehicles.RT Off-Road's upgraded Sway Bar Links are an affordable upgrade that increases performance and handling. Not only will your vehicle perform better with our upgraded polyurethane bushing and boots, but the product will last longer than the factory rubber pieces it replaces. All sway bar links install in place of the factory link.Black powder coated body with blue polyurethane boots and bushings; Polyurethane bushings provide long lasting performance and handling; Installs using factory hardware.

Référence : 51-JS-5970

Heavy Duty Chrysler 8.25″ Differential Cover; 3/8″ Thick Forged Steel w/ Ribs to Increase Strength; Semi-Gloss Black Powder Coat.Fill Plug Located Higher Than Stock for a Higher Fluid Capacity; Mounting Surfaces Machined Flat to Prevent Leaks; Includes Flanged Hex Bolts, Recessed Fill Plug and RTV.

Référence : 51-JS-7002

Complete Rear Performance Kit Including 2 Drilled & Slotted Rotors, Pad Set, Parking Brake Shoes and All Hardware.High Performance Brake Rotors from RT Off-Road are designed for the most extreme abuse. These Brake Rotors were tested on: the steep descents in Moab, UT; stop and go traffic in Boston, MA; and the long range treks in-between. Each brake rotor is machine slotted and cross drilled to provide maximum cooling. This drastic cooling helps eliminate brake fade and potential warping. The design rapidly expels friction gases, debris, and water from the rotor and pad surface. You can expect greater braking response, increased performance, longer life, and a sporty new look.

Référence : 51-JS-6921

Front Left Side Marker Light; Clear Lens w/ Amber Bulb.

Référence : 51-JS-6894

RT Off-Road's upgraded Sway Bar Links are an affordable upgrade that increases performance and handling. Not only will your vehicle perform better with our upgraded polyurethane bushing and boots, but the product will last longer than the factory rubber pieces it replaces. All sway bar links install in place of the factory link.Black powder coated body with blue polyurethane boots and bushings; Polyurethane bushings provide long lasting performance and handling; Installs using factory hardware.

Référence : 51-JS-5975

Heavy Duty Dana 44 Differential Cover; 3/8″ Thick Forged Steel w/ Ribs to Increase Strength; Red Powder Coat; Fill Plug Located Higher Than Stock for a Higher Fluid Capacity; Mounting Surfaces Machined Flat to Prevent Leaks; Includes Flanged Hex Bolts, Recessed Fill Plug and RTV.Protect high-dollar differentials with a Heavy Duty Differential Cover from RT Off-Road. These covers are constructed of 3/8″ high grade forged steel with a raised fill plug for extra oil capacity. They feature strengthening ribs to ensure a broken or peeled differential cover doesn't cut the day short. The mating surface is machined flat to ensure a leak-free fitment. All covers are finished in a red powder coat and includes flanged hex bolts, recessed fill plug and RTV.

Référence : 51-JS-7059

Complete Rear Performance Kit Including 2 Drilled & Slotted Rotors, Pad Set, Parking Brake Shoes and All Hardware.High Performance Brake Rotors from RT Off-Road are designed for the most extreme abuse. These Brake Rotors were tested on: the steep descents in Moab, UT; stop and go traffic in Boston, MA; and the long range treks in-between. Each brake rotor is machine slotted and cross drilled to provide maximum cooling. This drastic cooling helps eliminate brake fade and potential warping. The design rapidly expels friction gases, debris, and water from the rotor and pad surface. You can expect greater braking response, increased performance, longer life, and a sporty new look.

Référence : 51-JS-6926

High Performance Front Cross Drilled and Slotted Brake Rotors from RT Off-Road are designed for the most extreme abuse. These Brake Rotors were tested on: the steep descents in Moab, UT; stop and go traffic in Boston, MA; and the long range treks in-between. Each brake rotor is machine slotted and cross drilled to provide maximum cooling. This drastic cooling helps eliminate brake fade and potential warping. The design rapidly expels friction gases, debris, and water from the rotor and pad surface. You can expect greater braking response, increased performance, longer life, and a sporty new look.Includes Front Left and Right Cross Drilled and Slotted Rotors.

Référence : 51-JS-6931

RT Off-Road's Clear Light Kits are a DOT-legal way to give the vehicle an all new look. These crystal clear lenses come complete with amber bulbs. The bulbs and lenses included in our kit will install directly into the factory wiring harnesse and body. Installation requires no modifications to the body and can be completed with basic hand tools. Includes left and right side marker lamps and two (2) amber bulbs.

Référence : 51-JS-6899

Front Stabilizer Bar Link Kit w/ Polyurethane Bushings and Boots; Not Designed For Lifted Vehicles.RT Off-Road's upgraded Sway Bar Links are an affordable upgrade that increases performance and handling. Not only will your vehicle perform better with our upgraded polyurethane bushing and boots, but the product will last longer than the factory rubber pieces it replaces. All sway bar links install in place of the factory link.Black powder coated body with blue polyurethane boots and bushings; Polyurethane bushings provide long lasting performance and handling; Installs using factory hardware.

Référence : 51-JS-5980

Référence : 51-JS-8139

Improve the performance, durability and look of your suspension with RT Off-Road's Heavy Duty Shackle Kit. The shackle plates and reinforcement sleeves are finished in a rich black powder coat. Installation is as simple as removing the factory shackle assemblies and installing the supplied shackles. Effectively lifts vehicles 3/4"; Heavy duty plate steel construction; Includes installation instructions.

Référence : 51-JS-5985

High Performance Front Cross Drilled and Slotted Brake Rotors from RT Off-Road are designed for the most extreme abuse. These Brake Rotors were tested on: the steep descents in Moab, UT; stop and go traffic in Boston, MA; and the long range treks in-between. Each brake rotor is machine slotted and cross drilled to provide maximum cooling. This drastic cooling helps eliminate brake fade and potential warping. The design rapidly expels friction gases, debris, and water from the rotor and pad surface. You can expect greater braking response, increased performance, longer life, and a sporty new look.

Référence : 51-JS-6936